The DMM is a professional instrument with TRMS measurement of AC/DC voltage, AC/DC Current (through external clamp), Resistance and Frequency. Additional features are MAX/MIN/AVG function, HOLD function and PEAK detection with Response Time of 1ms, useful for surge currents detection. The Safety Tester features allow to perform test on electrical plants according to VDE0413. Measures of Continuity, Insulation, Global Earth value (also with 0.1W resolution), RCDs test, phase sequence indication and phase coincidence (using only one Test Lead even just touching even insulated cables or two Test Leads) and Leakage current (with HT96U clamp + NOCANBA connector) will be easily performed thanks to this new extremely compact instrument. An innovative function (AUTOTEST) automatically performs main safety checks in the plant (Earth Resistance measurement, RCD Test, Insulation Test) just connecting the instrument to a socket and pressing the TEST button. The instrument will give you a final response (OK or NOT OK) about the safety of the plant under test. Finally the LAN checker function allows you to check if the wire mapping in a LAN cable is correct or not with easy indications about the found errors, which will guide you though the troubleshooting. M75 is completed by a modern selector function knob, a large numeric display for easy readings of measurements and a protection rubber holder to prevent accidental damaged.

STANDARD

FUNCTION

DMM SECTION

• DC Voltage
• AC TRMS Voltage
• AC TRMS Current with External Clamp
• AC TRMS Leakage current with external clamp (optional)
• DC Current
• Resistance
• Continuity test with buzzer
• Frequency with test leads
• Frequency with External Clamp
• MIN/MAX/AVG functions
• PEAK function with response time 1ms
• HOLD function

SAFETY TEST SECTION

• Continuity test of protective conductors with 200mA
• Insulation Resistance measurement with 500VDC
• Trip-out time of RCDs type AC Standard with test current of 30mA, 30x5mA, 100mA, 300mA
• Global Earth Resistance without RCD tripping
• Phase sequence indication at 1 or 2 wires
• Phase coincidence indication at 1 or 2 wires
• Leakage current (with HT96U optional clamp + NOCANBA connector)
• AUTOTEST function: automatic sequence test of Global Earth Resistance + RDC test + Insulation test with OK / NOT OK indications LAN SECTION
• Test executed on twisted pairs cables UTP and STP with RJ45 connector
• Wire mapping control of following wrong conditions:
• OPEN, SHORT, CROSS, REVERSE, SPLIT, MISWIRE message at display
• Quickly selection of cables pairs
• Automatic detection of remote control units (from #1 to #8)
• AutoPowerOFF
• Low battery indication.

ACCESSORIES

Included accessories:

• HT4003: 400A AC clamps
• C2075: two safety banana + Shuko plug cable
• KIT0075: kit of 2 Test leads + 2 alligator clips
• N° 2 Remote identifier # 1, # 2
• N° 3 Patch cables, 30 cm, RJ45  RJ45 connectors
• BORSA75: Carrying bag
• Calibration Certificate ISO9000
• Instruction manual
• Warranty card

Optional accessories:

• HT96U: leakage current clamp 1-100-1000A/1V 54mm max diameter
• NOCANBA: adaptor for connection HT96U clamp
• REM38: N° 6 Remote unit # 3, # 4, # 5, # 6, # 7, # 8
• REM3: remote unit #3 + connection cable RJ45-RJ45
• REM4: remote unit #4 + connection cable RJ45-RJ45
• REM5: remote unit #5 + connection cable RJ45-RJ45
• REM6: remote unit #6 + connection cable RJ45-RJ45
• REM7: remote unit #7 + connection cable RJ45-RJ45
• REM8: remote unit #8 + connection cable RJ45-RJ45